FilClean™ Bag Filters & Magnetic Inserts
For Machine Tool Coolants
FilClean™ BHQ Single Round Bag Filter Housings with Quick Opening Clamp Design
Offers full selection of replaceable bag filters and flow rates 5- 225 gpm with basket only. These housings can accommodate standard #1, #2, #3, #4 and #12 size bag filters. See full features below.
FilClean™ BHMR Multiround Bag Filter Housings
Offers full selection of replaceable bag filters and flow rates up to 4000 gpm. These housings can accommodate standard #2 size bag filters. See full features below.
MaGFil™ Magnetic Reusable and Cleanable Insert
For bag filter prefiltration of ferrous particles. Removes ferrous particles from liquid flow increasing filter bag life. Compatible with FilClean™ BHQ filter housings. See full features below.
Product Specs & Ordering Info
Download Literature
FilClean™ BHQ Features
- Quick Open Clamp Design
- Flow Rates 5-225 gpm with Basket Only
- Built in USA
- Accommodates standard #1, #2, #3, #4 and #12 size bag filters
- All housings supplied with vent drain and gauge ports
- Available in Carbon, 304 or 316 SS
- NPT or Flanged Inlet/Outlet ports
- Removable Adjustable Height Legs**
- Epoxy Powder Coat Finish
- Rated at 150 PSIG @ 200° F
Full Selection of Replaceable Bag Filters
- Nylon Mono-filament: 10 to 1000 microns
- Polyester Felt: 1 to 200 microns
- Polyester Multi-filament: 150 to 800 microns
- Polypropylene Felt: 1 to 200 microns
- Oil Absorbent: 25 microns
- All micron ratings nominal
- Contact MSC for special requirements
| Max Flow Rate* | Housing Size | Basket Size (inches) |
|---|---|---|
| 50 gpm | Size 3 | 6 |
| 50 gpm | Size 4 | 12 |
| 100 gpm | Size 1 | 15 |
| 200 gpm | Size 2 | 30 |
| 225 gpm | Size 12 | 30 |
*Basket only: flow rates are less with filter bag installed.
Request a Quote
FilClean™ BHSB Features
- Easy Swing Bolt Lid Design
- Flow Rates tp 500 g[, with Basket Only
- Built in USA
- Accommodates standard #1, #2, #3, #4, #8, and #12 size bag filters
- All housings supplied with vent drain and gauge ports
- Available in Carbon, 304 or 316 SS
- NPT or Flanged Inlet/Outlet ports
- Removable Adjustable Height Legs
- Epoxy Powder Coat Finish
- Available Pressure Ratings at 150 per 300 PSIG
Full Selection of Replaceable Bag Filters
- Nylon Mono-filament: 10 to 1000 microns
- Polyester Felt: 1 to 200 microns
- Polyester Multi-filament: 150 to 800 microns
- Polypropylene Felt: 1 to 200 microns
- NOMEX High Temperature Bags
- Oil Absorbent: 25 microns
- All micron ratings nominal
- Contact MSC for special requirements
Request a Quote
FilClean™ BHMR Features
- High Flow Low Pressure Drop
- Flow Rates Up to 4000 GPM
- Accommodates standard #2 size bag filters
- Available in Non-Code and ASME Options
- Available in Carbon, 304 or 316 SS
- 180 Degree Bottom In - Bottom Out
- Lid Lifting Davits Standard
- 159 PSI Max Operating Pressure
- Various Basket Mesh Sizes Available
Full Selection of Replaceable Bag Filters
- Nylon Mono-filament: 10 to 1000 microns
- Polyester Felt: 1 to 200 microns
- Polyester Multi-filament: 150 to 800 microns
- Polypropylene Felt: 1 to 200 microns
- Oil Absorbent: 25 microns
- All micron ratings nominal
- Contact MSC for special requirements
Request a Quote
MaGFil™ Magnetic Inserts
Features:
- Removes ferrous particles from liquid flow increasing filter bag life.
- All 304 stainless construction resists wear and damage
- Fits a variety of Bag Filter Vessels
- EPDM (Ethylene Propylene Diene M) rubber bumpers to protect fabric bags
- Less than 5 seconds to clean - remove magnet from stripper sleeve and magnetic particles drop off into waste pan
- Never loses power
- Can reduce bag filter usage by 15 to 1. Contaminant and cleaning interval dependent
- Typical savings of 6:1 to 12:1 are common
- Multiple magnetic types available: Depending on application, removal strength and dirt holding requirements - Ceramic, Neodymium or Alnico.
| Magnet Length | Bag Filter Size | Bag Filter Dim. |
|---|---|---|
| 15 in. | 1 | 7" x 16-12" |
| 30 in. | 2 | 7" x 32" |
| 8 in. | 3 | 4" x 8" |
| 14 in. | 4 | 4" x 14" |
| 20 in. | 8 | 5.6" x 21" |
| 20 in. | 9 | 5.6" x 32" |
| 34 in. | 12 | 82" x 32" |
Request a Quote
| Magnet Type--> | Ceramic (strong) | Alnico (stronger) | Neodymium (strongest) |
|---|---|---|---|
| Gauss on Magnet Tube Surface | 1200 Gauss | 1350 Gauss | 5500 Gauss |
| Capacity (steel chips) per 4" of magnetic length | 1 lb | 1.55 lbs | 2.45 lbs |
| Pull Force (for comparison purposes) | 25 lbs | 35 lbs | 125 lbs |